Garage door weather stripping isn’t one part. It’s the bottom seal on the door, the stop molding around the frame, and sometimes a threshold strip glued to the floor. If you see light under a closed door, or snow drifts in along the bottom, one of them has quit. The bottom seal usually goes first. If the aluminum channel it slides into is still straight, most homeowners can replace it themselves in an hour or two. Around the Iowa Great Lakes, October is the month to do it. The seal is still soft enough to work, and it hasn’t frozen to the concrete yet.
Key Takeaways
- Light under a closed door, or snow along the bottom, means the seal is done.
- The bottom seal is a safe DIY job if the retainer is straight and the door still balances.
- Don’t touch the bottom brackets. The lift cables are under tension there.
- A gap that’s wider on one side usually isn’t a seal issue.
- New seals stop drafts. They won’t make an uninsulated door hold heat.
How do you know your garage door seals are shot?
Close the door on a sunny afternoon and kill the lights. If you see light along the floor or up the sides, that’s your answer.
The weather tells you too. A line of snow inside after a windy night, a puddle that keeps coming back in the same corner, mouse droppings along the wall, these all mean the seal has quit. We find that a lot in lake homes that sit empty midweek.
A seal that has gone flat and hard, or has a corner torn from being frozen to the floor, isn’t sealing anymore. It’s still hanging there, but it’s lost its job.
What are the different kinds of garage door weather stripping?
There’s the bottom seal. That’s the rubber or vinyl strip on the bottom edge of the door. On most steel doors, it slides into an aluminum channel called a retainer, screwed to the bottom section. Retainers aren’t one size fits all. Some take a flat “T” on each edge, others a round bead, and sizes vary by brand. Clopay’s own weather seal instructions say to match the seal to the retainer before you start. Older wood doors often have no retainer at all.
Then there’s the perimeter seal, or stop molding. It’s the trim with a soft flap nailed around the sides and top of the opening. The flap presses lightly against the face of the closed door.
Some garages also have a threshold. It’s a rubber hump glued to the floor where the door lands. It helps on a slab that has settled or slopes toward the garage. The bottom seal can only stretch so far.
Rubber or vinyl: which holds up in an Iowa winter?
Both work, and both wear out. Clopay’s seal buyer’s guide lays out the tradeoff. Rubber stays more flexible and seals better on rough concrete, though it can stiffen over time in very cold climates. Vinyl holds up to moisture and sun, but it is less flexible in the cold.
Our take for this area: on an attached or heated garage, or a slab with some dips, we lean rubber for the bottom seal. It stays softer on a 10-below morning. On a detached garage or a machine shed, vinyl is fine and costs less. For the sides and top, vinyl stop molding is the usual choice. The stiff back holds the nails, and the soft flap does the sealing.
How do you replace a garage door bottom seal?
This is one of the few garage door jobs we’ll walk you through. If the door balances and the retainer is straight, this is yours to do. If it doesn’t, stop and call.
Plan on an hour or two, with a helper if you can get one. You’ll need the matching seal, two C-clamps or locking pliers, a flat screwdriver, a utility knife, and a spray bottle of soapy water.
- Figure out what you have. Cut a few inches off one end of the old seal and take it to the store, or call the door’s manufacturer with the model.
- Disconnect the opener. With the door fully closed, pull the red emergency release cord. Then unplug the opener so nobody hits the button while you’re under there.
- Lift the door by hand and clamp it. Raise it until the bottom edge is at a comfortable working height. Then clamp each track just below the bottom rollers so the door can’t come down. If the door is heavy to lift, or won’t stay where you leave it, stop. The springs are out of balance, and that’s a job for a tech.
- Pull out the old seal. Many retainers are crimped or screwed at the ends to keep the seal from walking out. Open the crimp with a screwdriver, or pull the screws, then slide the seal out the end.
- Clean the channel. Scrape out dirt and old bits of rubber. A dirty channel is why a new seal hangs up halfway across.
- Slide in the new seal. Spray the channel and the seal edges with soapy water. Start both edges into the retainer, then feed it across while your helper pulls from the far end. If the seal rode home in a cold truck, bring it in the house overnight first. It slides much easier warm.
- Finish the ends. Clopay says to leave about two extra inches and tuck it in on itself, because the seal shrinks. Re-crimp the ends or put the screws back.
- Unclamp and test. Hold the door while you take the clamps off. Lower it by hand, then reconnect the opener. Run it a few times, then do the daylight check again.
Don’t loosen the bottom brackets on the lower corners of the door. The lift cables connect there, and they’re under heavy tension. DASMA, the door industry’s safety association, says leave that to a trained technician.
What about the sides and top of the door?
Stop molding usually outlasts the bottom seal, but the flap gets hard and pulls away from the door over time. To replace it, close the door, pry off the old strip, and nail the new one with galvanized nails. The flap should just touch the door along its full length.
Just touching is the goal. Set it too tight and the door drags. The opener works harder. On a cold morning, that tight seal can be the reason the door won’t open. If the wood jamb behind the old molding is soft or crumbling, fix that first. That’s a carpentry job more than a door job.
What if the bottom seal freezes to the floor?
It happens every winter here. A wet afternoon, a hard freeze, and the door won’t budge in the morning. Don’t keep hitting the button. The opener will strain against it until the seal tears or the opener reverses.
Break it free gently with a plastic putty knife along the seal, or a hair dryer on the frozen spots. Once it’s open, sweep the slush away from where the door lands so you aren’t doing this again tomorrow.
When should you call a tech instead?
When in doubt, call. A new seal is cheap. A crooked door left alone is not.
- The retainer is bent, cracked, or corroded. A new seal won’t hold in a damaged channel, and on many doors the retainer comes off near those bottom brackets.
- The bottom section is rusted through or rotted. That’s a panel replacement, not a seal.
- The gap is bigger on one side. A door that hangs crooked can mean a cable or drum problem. A new seal just hides it until something lets go.
Will new seals make the garage warmer?
New seals stop drafts, and for a lot of garages that’s the cheapest fix there is. What they won’t do is make a single-layer steel door hold heat. If the garage is attached, heated, or has a bedroom over it, the door itself may be the bigger issue. That’s where an insulated garage door comes in.
We won’t sell you a new door you don’t need. But if the draft is coming through the door itself, a seal won’t fix it.
While you’re sealing things up, check the door between the garage and the house. That’s the one that keeps car exhaust out of your living space. The Department of Energy’s Building America program recommends it be self-closing and weatherstripped, with a tight threshold sweep.
Would you rather we handle it?
We replace bottom seals, retainers, and stop molding on any brand of door as part of our garage door service and repair. While we’re there, we check what usually causes seal trouble in the first place. A door that doesn’t sit level, worn rollers, springs out of balance. If the seal is the only problem, the seal is all we fix.
FAQ
How often should garage door weather stripping be replaced?
There’s no set schedule. Replace it when you see light under the door, water or snow getting in, or a seal that’s flat, cracked, or stiff. Check it every fall. A seal that’s half shot in October won’t get better in January.
How much does a garage door bottom seal cost?
The seal is an inexpensive part. A complete kit with seal, retainer, and screws from Action Industries is listed at about $42 to $73 as of November 2026, depending on door width. Local prices vary, and the cost goes up if the retainer or bottom section also needs work.
Why is my new bottom seal not sealing on one side?
Either the floor dips, or the door isn’t hanging level. Put a level on the bottom of the closed door. If the door is level, a thicker seal or a threshold will fill the low spot. If the door is crooked, have it looked at.
Questions about your seals, or want us to take care of them? Call (712) 332-2866 or send us a service request. We work on garage doors in Spirit Lake, Okoboji, Arnolds Park, Milford, Spencer, and across the Iowa Great Lakes.
